Fuel Gas Cartridge Strainer

Flange Fuel Gas Cartridge Strainers

Model
KRTG1B4F-16C
Design Standard
GB/T36051-2018
Structure&Length Standard
GB/T36051-2018
Flange Standard
GB /JB / HG / DIN
Flange Hole Size Standard
GB/T9116-2010+Spiral groove
Design Temperature
-29~+60℃
Nominal Diameter (MM)
DN25-DN400
Nominal Pressure (MPA)
1.6-6.3
Body Material
carbon steel
Filter Screen Material
SUS304
Wire Mesh Material
SUS304
Gasket
PTFE
Sealing surface
RF/FF
Connection Type
Flange
Surface
epoxy resin
Applicable Medium
gas
Contact Now
Flange Fuel Gas Cartridge Strainers
KRTG1B4F-16C
Fuel Gas Cartridge Strainers
Cartridge Strainers
Flange Fuel Gas Cartridge Strainers
Flange Fuel Gas Cartridge Strainers
Flange Fuel Gas Cartridge Strainers

Product Introduction

 

  The KRTG1B4F strainer is an indispensable device in the pipe system that conveys gas and other media. It is generally used in such transportation and distribution systems as gas off-take stations, gas distribution stations and gas stations, playing its important role in protecting pressure controllers, flow meters, valves and other equipment in the system. 

 

  • Body Material: A105(more details please check the follow drawing)
  • Applicable medium:  gas
  • Diameter: DN25-400mm
  • Nominal Pressure: 1.6-6.3MPa
  • Design temperature:-29ºC~ +60ºC
  • Connection type: flange
  • Filter meshes: 50 meshes or customer requirements
  • Design Standard: GB/T36051-2018
  • Structure&Length Standard: GB/T36051-2018
  • Flange Standard: GB /JB / HG / DIN

 

Features of Product

  1. It is used to filter particulate impurities in natural gas, liquefied petroleum gas and other transport media, and protect the valves, flow meters, pressure regulation and other equipment.
  2. The strainer is composed of shell, filter element, removable flange (or quick opening device) upper cover and sewage outlet. Removable flange cover is convenient for removing or replacing the filter element.
  3. The filter element of KMO is made of stainless steel wire mesh or non-woven fabric. The filter area is large and the pressure loss is small. The filtered particles are concentrated at the bottom of the filter and discharged from the sewage outlet. The stainless steel wire mesh filter element can be washed and reused many times.
  4. The filter screen can be set according to the user's needs. The filter accuracy is generally divided into 5μm (non-woven fabric), 20μm and 50μm.
  5. The product can be optionally equipped with a differential pressure gauge. When the filter screen is blocked and the pressure loss value increases, please remove and wash the filter element or replace a new one.
  6. The product has such features, like small body shape, high filtration accuracy, good filtration effect, low cost, short drainage time, and easy to install and maintain. For small models, it only takes 5-10 minutes to install.

 

Notes for Use

  1. Keep the filter cavity clean before installation to prevent impurities from entering and affecting the use effect.
  2. When the strainer is tested for hydraulic strength, the intake valve should be closed firstly. After the test is completed, use 0.6MPA air pressure to conduct airtightness test on the strainer, differential pressure gauge and pressure guide tube. After the pressure is stabilized, opening the two intake valves slowly at the same time to avoid damage to the differential pressure gauge caused by excessive unilateral pressure 
  3. According to the working conditions on site, it is recommended to periodically drain and clean the filter.
  4. KMO reminds the user that it is necessary to clean the filter element when the differential pressure gauge shows that the difference of the inlet and outlet pressure reaches 0.03MPA (or specified by the user). The cleaning step is that: ①cutting of the inlet and outlet valves of the filter to ensure that there is no pressure and medium in the inner cavity; ②taking out the detachable filter element and using a brush to gently remove impurities; ③reloading. If the cleanliness of the filter element still cannot meet the demand after cleaning, it is recommended to replace with a new filter element.
  5. After each cleaning, you need to re-test to ensure the tightness of the product, and replace the air in the filter with nitrogen.
  6. Closing the intake valve before venting, after the pressure is stable then slowly open the two intake valves at the same time , to avoid damage to the differential pressure gauge caused by excessive unilateral pressure.

 

Strainer Process Flow

FILTER PROCESS FLOW

Model Making Method

MODEL MAKING METHOD

MODEL MAKING METHOD

KRTG1B4F-16C Gas Cartridge Strainer

KRTG1B4F-16C Fuel Gas Cartridge Strainers

KRTG1B4F-16C Drawing

KRTG1B4F-16C Fuel Gas Cartridge Strainers

Performance Parameters

Performance parameters

Main Technical Parameters

Main technical parameters

Filtering Precision Parameter Table

Filtering precision parameter table

FAQ:

Q: Are you manufacture or trading company? 
A: We are manufacture and our factory is in in Oubei Town, Yongjia County, Wenzhou City, Zhejiang Province.

Q: What is your products' MOQ?
A: 10pcs.

Q: Can you provide the sample for free?
A: Yes, we can provide the sample for free, but you need bear the delivery cost.

Q: If products have some quality problem, how would you deal with?
A: We will responsible for all the quality problems.

Q:Can we print our logo on your products?
A: Yes, just let me know if you need.


 

Feedback
Product Recommend